![]() ![]() There could be a few settings or procedures that could completely fix your problem, independent of anything I’ve suggested. I’d be curious to know if something similar might be happening with your material.Īgain, this is just the opinion of one not-very-well-informed person. In a scenario like you described where the lids are left off the totes to dry for a day before processing, the top layer can get sort of gummy and crunchy, kind of like leaving a full bowl of tomato soup out for too long - a skin forms on the top, but the stuff under is still the same as it was before the skin formed. In my opinion cannabis shouldn’t be exposed to humidity lower than 55% for fear that it will lose aroma and potency. Regarding the drying, I would not let it dry out completely. The rocketbox isn’t something that I’m super familiar with so I can’t comment on the settings or operation of it directly, but hopefully is able to help out and get to give a bit more relevant information to you. These are about where my ideas end regarding your problem. Ive played with settings, and loosening screws, it just seems like really hit or miss. Possibly not gentle enough for anything to travel down. I’m wondering if my stage 1-2 settings are too aggressive? Our product is real fine, but it seems like some of the larger material, tiny stems, will congregate at the bottom and packs solid at the top. Most our failed joints are loose necks, we will usually roll the necks in our fingers until its finer, then tap tap on clean table then tamp tamp the heads. So am I looking for a completely dry grind? Or there is actually a sweet spot, cause typically Ill just try to dry my product out the day before “lids off totes and set by our outlet exhaust fan” No air actually blows onto the grind, the exhaust fan pulls air outside and will just setup my totes next to them. We do use those racks for product that’s far to moist. I’m able to distribute one of my “totes” over about 3 of those pans if I remember correctly. However I don’t believe we have any covers for them. Those racks, we literally have about 80 of them. Once a week if any of my stuff doesn’t get handled, Ill toss it and burp all my totes. Ill grind, then fill totes which can range from 2k-5k grams of “raw” material. Now for MY material, Ill leave out my grind process for now unless you want to hear that process also. Our product holding and our cure/hang rooms stay at about 62-65% Usually the oldest stuff is no older then 2 months in the bag (trim or reject material) Then any raw flower goes into large totes. Then after that trim goes into turkey bags until my team pulls for pre-rolls or extract, the bags typically holding in the 2k-3k gram range. CBD strains (Sour Cyclone) Ill sometimes grind up to q/oz buds.Īfter harvest, I think the guys are curing/hanging for a full week, then sometimes over the weekend depending on where harvest falls in the week, typically we harvest every Friday though. Trim team would know a bit more being as that’s who has the most hands on, I can find out though for sure.īut from my understanding, 1gram buds or less for anything besides CBD strains. So basically, this is our process “from my understanding”. We had some a professional extract team come in and step up our extract game like immensely, so now I’m wanting to get this tackled. Literally any information or questions I’m an open book at this point. Probably takes up a solid 35% of the time process. Our grind process also produces A++ product but It’s tedious and time consuming. We run about 20 different strains and I’m wondering if you guys who are are actually presetting/per strain? I’d really hate to setup 20-30 different defaults if the system could even have that many profiles I’m not sure?Īt the moment were producing around 4-6k a day with a 3 man team. So far Ive I’ve got 2 setups that I use, one more aggressive, and one softer settings for my finer grinds. Still takes extra time for my team to lay hands on product a second time and I really want to eliminate that issues. I still cant seem to get the right fill consistency.Ĭonstantly having issues with loose necks and failed fills. Ive been running out Rocketbox for about 4 months now while playing with settings and fine tuning. I’m the head of “joint operations”… Fun title play. So I currently work at a tier 3 facility in Washington State.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |